SG4 Fixed Blade With Bolsters and Handle Pins
- MPN:
- SG4BL-STD
- Gift wrapping:
- Options available
Bulk discount rates
Below are the available bulk discount rates for each individual item when you purchase a certain amount
| Buy 3 or above | and pay only $95.00 each |
Description
SG4 Blade, Stainless Steel
Stainless blade in 440C steel in a gift box, with steel bolsters and steel handle pins included.
All you need is a set of handle scales, to make your own handle.
The flat ground blade is hardened, sharp and ready to go.
Work required:
- Tape blade up well to protect it and you while working
- Glue on the steel bolsters and pins with araldite or similar 2-component epoxy
- Peen bolster pins until they stick by hammering them lightly (optional step as they are epoxied on)
- Take handle scale to blade, drill through blade for handle pins 1/4"
- Repeat on other side
- Glue on handle scales with epoxy glue and clamp well
- Shape handle scales with belt sander, files or similar
- Sand well to has high grit as possible
- Seal with UBHF, axe wax or other product
General Kit Specifications
SG4 "Standard Grind"
Skill Rating: Level III
Blade Steel: 440C stainless steel
(Heat Treated to 56-58 rc.)
Blade Finish: 600 Grit Satin Finish
Blade Length: 4.40 Inches
Handle Length: 4.49 Inches
Overall Length: 8.86 Inches
Pins: Stainless
Bolster Pin Holes: .187 inches
Handle Holes: .250 inches
Thong Hole: .250 inches
Gift Box = Yes
SG4 "Standard Grind"
Skill Rating: Level III
Blade Steel: 440C stainless steel
(Heat Treated to 56-58 rc.)
Blade Finish: 600 Grit Satin Finish
Blade Length: 4.40 Inches
Handle Length: 4.49 Inches
Overall Length: 8.86 Inches
Pins: Stainless
Bolster Pin Holes: .187 inches
Handle Holes: .250 inches
Thong Hole: .250 inches
Gift Box = Yes
Related Products
Related Products
G10 handle pins
$2.00
G10 Pins for handles (1/8" or 1/4" or 3/16" )
Select colour and diameter in options
G10 pin for using in knife handles, this is for one pin of length approx 250-300 mm and with a diameter of 1/8"...
Bolster R30
$12.00
Bolster R30, pre-shaped guard/front
These stamped out bolsters save time when fitting a stick tang blade to the handle.
Select brass, copper or nickel silver under Options.
The bolster is about 30 x...
Carbon Fiber Bolster
$19.00
Carbon Fiber Bolster Carbon fiber plates. Carbon fiber has exceptional strength, is lightweight and durable which make it a highly sought-after material. With their superior performance and stunning...
Out of stock
Bolster R24, brass
$10.00
Bolster R24, Brass Brass version of the bolster R24. The bolster is about 24 x 17 mm and 3 mm thick with a 2 mm slit. These are stamped out and most blade/bolster combina
Bolster 3580B, Brass
$12.00
Bolster R30, Brass Brass version of the bolster R30. The bolster is about 30 x 19 mm and 3 mm thick, with a slit of 2 x 13 mm cut out. These are sta
Bolster R35, Brass
$12.00
Bolster R35, Brass (35 x 18 x 3 mm, slit 3 x 12 mm) Brass version of the bolster R35. Bolsters is an easy way to get a good looking fit between handle and blade. The handle piece can then have a...
Bolster R35E, Brass
$12.00
Bolster R35E, Brass (35 x 17 x 3 mm, slit 3.2 x 19 mm) Brass version of the bolster R35E. (note the Extended or longer slit than on the R35) Bolsters is an easy way to get a good looking fit...
Bolster V35, Brass
$12.00
Bolster V35, Brass (35 x 17 x 3 mm, slit 3 x 14 mm V shaped) Brass version of the bolster V35 with a V slit thinner in one end. The difference between V35 and "V35 Extended" is the length of the...