Corby Bolt 1/4", Brass
- Gift wrapping:
- Options available
Bulk discount rates
Below are the available bulk discount rates for each individual item when you purchase a certain amount
| Buy 4 - 19 | and pay only $2.25 each |
| Buy 20 or above | and pay only $2.00 each |
Description
Corby Bolt, Brass (1/4", 6.35 mm)
Medium size corby bolt in brass, for securing handle scales to full-tang knife blades.
These are often used in addition to epoxy glue, for both looks and additional attachment strength of the handle scales.
The bolt has thicker end pieces (6.35 mm / 1/4") with screwdriver slots in them.
The centre section is 4.6 mm thick and is the part that goes through the blade.
The bolt is threaded, consisting of two pieces that when tighetend is ground down to sit flush with the handle scales.
total length 25 mm
each shoulder 8 mm
middle section 9 mm
screws out to about 13 mm middle section, adding max 4 mm if not screwing them all the way in
Example of corby bolts in Danish made Raffir "Grand Chef" blade, knife by Åge Fjeldberg:
Related Products
Related Products
Corby Bolt 1/4", Copper
$3.50
Corby Bolt, Copper (1/4", 6.35 mm) Medium size corby bolt in copper, for securing handle scales to full-tang knife blades. These are often used in addition to epoxy glue, for both looks and...
Corby Bolt 1/4", Stainless Steel
$3.50
Corby Bolt, Stainless Steel (1/4", 6.5 mm) Medium size corby bolt in steel, for securing handle scales to full-tang knife blades. These are often used in addition to epoxy glue, for both looks and...
Out of stock
Corby bolt drill w/counter sink 1/4"
$39.00
Corby Countersink with pilot drill bit, for 1/4" Corby Bolts Made in Germany, set for installing corby bolts of size 1/4" Comes with pilot drill 4.6 mm, and the "countersink" the short stubby drill...
Corby bolt drill w/counter sink 5/16"
$39.00
Corby Countersink with pilot drill bit, for 5/16" Corby Bolts, Loveless bolts etc Set for installing corby bolts of size 1/4" Comes with pilot drill 4.6 mm, and the "countersink" the short stubby...
Lanyard Tube, Brass 1/4"
$5.00
Brass Lanyard Tube, 1/4" For EnZo blades, lanyard tube for knife making. Size is 1/4", 6.35 mm as outer diameter. Length 22 mm, inner diameter 4.9 mm. Both outside and inside edges of the tube is...
Brass pin for handles, 1/4"
$5.00
Brass Pin, 1/4" for handle pins (6.35 x 145 mm ) Brass pin for using in knife handles, this is for one pin of length approx 145 mm and with a diameter of 1/4" (6.35 mm). Using pins is a faster,...
Lanyard Tube Length, Brass 1/4"
$5.00
Brass Lanyard Tube, 1/4" for handle pins (6.35 x 145 mm ) Brass lanyard tube for using in knife handles, this is for one pin of length approx 145 mm and with a outside diameter of 1/4" (6.35 mm)...
Loveless Bolts 1/4" - pack of 5
$29.00
Loveless bolts 1/4" (6.35 mm) - pack of 5 Strong way to attach scales to fulltang knife blades. Bolt is Stainless Steel with brass cylinders as "nuts". Adjusts for handle width, epoxy thread and nut...
Brass 1/4" Kydex Eyelets for Sheath Making (#8-8), pack of 20
CKK
$15.00
Kydex Rivets or eyelets (1/4"), pack of 20 (Brass finish) Flaring Eyelets for 2 mm kydex with 1/4" diameter#8-8(Polished brass finish)These are the indust