Corby Bolt 1/4", Copper
- Gift wrapping:
- Options available
Bulk discount rates
Below are the available bulk discount rates for each individual item when you purchase a certain amount
| Buy 3 - 19 | and pay only $2.25 each |
| Buy 20 or above | and pay only $2.00 each |
Description
Corby Bolt, Copper (1/4", 6.35 mm)
Medium size corby bolt in copper, for securing handle scales to full-tang knife blades.
These are often used in addition to epoxy glue, for both looks and additional attachment strength of the handle scales.
The bolt has thicker end pieces (6.35 mm / 1/4") with screwdriver slots in them.
The centre section is 4.6 mm thick and is the part that goes through the blade, total length 25 mm. Each head section is 8 mm long and 6.3 mm in diameter.
The bolt is threaded, consisting of two pieces that when tightened is ground down to sit flush with the handle scales.
total length 25 mm
each shoulder 8 mm
middle section 9 mm
screws out to about 13 mm middle section, adding max 4 mm if not screwing them all the way in
Related Products
Corby Bolt 1/4", Brass
$3.50
Corby Bolt, Brass (1/4", 6.35 mm) Medium size corby bolt in brass, for securing handle scales to full-tang knife blades. These are often used in addition to epoxy glue, for both looks and additional...
$3.50
Corby Bolt 1/4", Stainless Steel
$3.50
Corby Bolt, Stainless Steel (1/4", 6.5 mm) Medium size corby bolt in steel, for securing handle scales to full-tang knife blades. These are often used in addition to epoxy glue, for both looks and...
$3.50
Corby bolt drill w/counter sink 1/4"
$39.00
Corby Countersink with pilot drill bit, for 1/4" Corby Bolts Made in Germany, set for installing corby bolts of size 1/4" Comes with pilot drill 4.6 mm, and the "countersink" the short stubby drill...
$39.00
Corby bolt drill w/counter sink 5/16"
$39.00
Corby Countersink with pilot drill bit, for 5/16" Corby Bolts, Loveless bolts etc Set for installing corby bolts of size 1/4" Comes with pilot drill 4.6 mm, and the "countersink" the short stubby...
$39.00
Copper pin for handles 1/4"
$5.00
Copper Pin, 1/4" for handle pins (6.35 x 145 mm ) Copper pin for using in knife handles, this is for one pin of length approx 145 mm and with a diameter of 1/4" (6.35 mm). Using pins is a faster,...
$5.00
Loveless Bolts 1/4" - pack of 5
$29.00
Loveless bolts 1/4" (6.35 mm) - pack of 5 Strong way to attach scales to fulltang knife blades. Bolt is Stainless Steel with brass cylinders as "nuts". Adjusts for handle width, epoxy thread and nut...
$29.00
Copper pin for handles, 1/8"
$5.00
Copper Pin, 1/8" Copper pin for using in knife handles, this is for one pin of length approx 28 cm and with a diameter of 1/8". Copper is an easy to work material, and takes a great shine...
$5.00
Copper Sheet, 1 x 120 x 240 mm
$27.00
Copper plate, 1 mm thick
Copper sheet or spacer material, approx 120 x 240 mm in size.
Used for spacer materials in handle construction, this is a single piece of copper approx one handle high and 6...
$27.00
Spacer Material, Copper 40 x 40 x 1 mm
$6.00
Copper plate, 1 mm thick (40 x 40 mm) Copper spacer material, min 4x4 cm in size. These are cut out and may need to be hammered flat before use. Drill a hole for the tang and insert these as...
$6.00